- #WINDOWS LIVE PROBLEMS TRIMBLE SURVEY CONTROLLER 3 UPGRADE#
- #WINDOWS LIVE PROBLEMS TRIMBLE SURVEY CONTROLLER 3 SOFTWARE#
In the RTCM box is shows that the base status indicator is green and both the GPS and Glonass satellite systems are green (if you want to change the satellite system, refer to the following section). Even if the accuracy of the base station is 1.5 to 2 m, the position accuracy of the rover module relative to the base station can still reach centimeter level.Īfter the survey is complete, Mission Planner will display the following page: If your application does not require UAV with high absolute geographic accuracy, you do not need to set the base station’s precision too high, resulting in long survey time.
It should be noted that the absolute geographic accuracy of the base station here will affect the absolute geographic accuracy of the rover module without affecting the relative accuracy between the base station and rover. Testing shows that, in an open area without shelter, to achieve the absolute accuracy of 2m takes a few minutes to reach the absolute accuracy of less than 30cm takes around an hour to reach the accuracy of 10cm takes a few hours.
The base station needs a certain amount of time to meet the accuracy requirements of your input. The green bar at the lower part of the Mission Planner page shows the satellites being detected and the signal strength related to each satellite. You will see the following page:ĭuring the survey process, the right box will show the current survey status: Position is invalid: base station has not yet reached a valid location In Progress: survey is still in progress Duration: The number of seconds that the current surveying task has been executed Observation: the number of observations acquired Current Acc: Absolute geographic accuracy that the current base station can achieve. Click on Restart, the ground station will transfer the data you have entered to the HERE + base module, the base module will start a new round of surveying. In the Time column, enter the minimum survey time you expect. In the SurveyIn Acc section, enter the absolute geographic accuracy that you expect your HERE + base station to achieve. Select the correct base module com port in the top left corner and click connect.
#WINDOWS LIVE PROBLEMS TRIMBLE SURVEY CONTROLLER 3 SOFTWARE#
Open the Mission Planner ground station software on your computer and go to the initial setup -> Optional Hardware -> RTK / GPS Inject page. During the base station setup, the rover and the UAV do not need to be turned on. For first time setup in a new location, click the Enter Base Position button, make sure the dialog box shows empty location information, as shown below:īase module setting using Mission Planner ¶.Open the Initial Setup > Optional Hardware > RTK GPS Inject screen.Pixhawk, Cube, etc) using Mission Planner Connect to the vehicle’s autopilot (i.e.Place the base station on a stable and elevated platform, such as a tripod. During operation, please place the base station in an outdoor environment with sufficient sky coverage to obtain a good satellite signal.Place vehicle and base stations so that their GPS antennas have a clear view of the sky (i.e.For UAV, HERE + rover module is connected to the autopilot GPS connector, telemetry module is connected to the TELEM interface. Before using, make sure the hardware is connected correctly: The base station module is connected to the computer port through USB a telemetry module is connected to another USB port of the same computer.To use HERE+ on a UAV, you need the following hardware:
If the process is interrupted, or if it is not responding for a long time, the modules will need to be power cycled and uploading needs to be done again.
#WINDOWS LIVE PROBLEMS TRIMBLE SURVEY CONTROLLER 3 UPGRADE#
If the uploading is successful, the upgrade interface is displayed in green if the upgrade is aborted, the interface is displayed in red. Uploading usually takes only a minute or less. In Flash Information Structure(FIS) File, select Flash.xml,which is located in the installation address of U-centre software.Ĭlick OK and wait for the firmware uploading to complete. In Firmware image, unzip and select the downloaded 1.30 Firmware.įor base module, chose the firmware with title: UBX_M8_301_HPG_130_REFERENCE_NEOM8P2.59a07babb501ba6a89ff87cac2f 2765f.bin For rover module, choose the firmware: UBX_M8_301_HPG_130_ROVER_NEOM8P0.3ee86a9e4775e3335e742b53527fa5 d0.bin Open the U-center software, click the connection button (as shown in the red circle), select the com port that corresponds to your base/ rover module.Ĭlick tools->u-blox 5 – 8 Flash Firmware Update, and click the settings as shown below: